H&R Wheel Spacers Volkswagen Jetta MK4 (98-05) 3mm 5mm 8mm 10mm 12mm 15mm 20mm 25mm 30mm

Details

Fitment Information

• Volkswagen Jetta Mk4(1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005)
• Volkswagen Jetta Mk4 TDI(1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005)
• Volkswagen Jetta Mk4 4Motion(2000, 2001, 2002, 2003, 2004)
• Volkswagen Jetta Wagon Mk4(2001, 2002, 2003, 2004, 2005)

Specs & Features

• Bolt Pattern: 5/100
• Center Bore:57.1
• Bolt or Stud:Bolt
• Thread Type:14×1.5
• Sold as a pair

• DR Series
• DR Series spacers fit between the wheel and hub, and require longer wheel bolts (ordered separately). Please verify bolt specifics before ordering (taper or round bolt head and shaft length.)
• DRA Series
• DRA Series spacers bolt to the hub with special wheel bolts (included) and provide new threaded holes for the existing wheel bolts.

Product Description

Wider is Better! H&R TRAK+ Wheel Spacers move your wheels and tires outwards so they are more flush with the fender instantly giving your vehicle the perfect stance. High end sports car manufacturers use every millimeter of fender space available in their design for the best looks and highest performance and so should you. With TRAK+ you can fill the gap in your fenders and GO WIDE!

TRAK+ Wheel Spacers are manufactured from a special proprietary alloy specifically developed for H&R that is lighter and has a higher tensile strength than 6061-T6 billet aluminum. H&R TRAK+ Wheel Spacers are hubcentric and feature a full contact hub just like the factory hub for even load force distribution and lateral support.

These are hub-centric flat disc type spacers which require the factory hub to center the wheels. Please measure the vehicle hub to verify sufficient height will remain to center the wheel after spacer installation.

If the hub face of your vehicle is 150mm (most vehicles have 135mm hub face,) alternative spacers are available. Please see list below.

DR = 8mm 162555719
DR = 10mm 202555713A
DR = 12mm 242555713
DR = 15mm 302555716
DR = 20mm 402555716
DRA = 20mm 4025572
DRA = 25mm 50255712
DRA = 30mm 60255712

All DR-Systems require longer wheel bolts. These must be ordered separately. When ordering wheel bolts, please follow these guidelines:

a) If possible, name the brand of wheel.

b) New bolts must be longer than the original bolts by the width of the wheel spacer used.

c) The bolt head must be identical to the existing bolt:
Taper 60 End digit 01
Round head for M12/d24 mm, for M14/d28 mm End digit 02
Round head for M12/d26 mm (e.g. OE VAG-wheels) End digit 03
Flat head for Porsche original wheels M14 x 1.5 End digit 06

d) Safety guidelines
(Minimum number of turns for wheel bolts / nuts):
M12 x 1.25 = 8.0 turns = approx. 10 mm of load bearing shaft length
M12 x 1.50 = 6.5 turns = approx. 10 mm of load bearing shaft length
M12 x 1.75 = 6.5 turns = approx. 12 mm of load bearing shaft length
M14 x 1.25 = 9.0 turns = approx. 12mm of load bearing shaft length
M14 x 1.50 = 7.5 turns = approx. 12 mm of load bearing shaft length
1/2″ UNF = 8.0 turns = approx. 11 mm of load bearing shaft length

e) Please ensure that the wheel bolts do not damage any part of the brake system (ABS sensors, etc.). Turn the wheel by hand and check clearance on the inside of the hub. The wheel should rotate freely. (Maximum tolerance for some vehicles is only 2mm — i.e. Rear Axle Mercedes.)

Careful attention must be paid to the vehicle hub height and inner wheel bevel measurements. Failure to follow the measurement guidelines below can result in serious damage to wheel spacers, wheels, and mounting hardware.